Web password wizard serial how to#
Web password wizard serial install#
Web password wizard serial serial#
Web password wizard serial password#
Web password wizard serial Pc#

Web password wizard serial password#

ssh user admin123 authentication-type password Switches running V200R007 and later versions use SSH and do not need to have this command configured. protocol inbound ssh //By default, switches running V200R006 and earlier versions use Telnet and need to have this command configured. The configuration methods in the two scenarios are the same. If the user name is a new one, you can configure a new STelnet login account.

If the user name is the original one, you can reset the password of the original login account.

Set the STelnet login authentication mode to password authentication, user name to admin123, password to and user privilege level to 15. Warning: This operation may affect online users, are you sure to change the user privilege level ? y local-user testuser password irreversible-cipher local-user huawei service-type telnet If the user name is a new one, you can configure a new Telnet login account. Set the Telnet login authentication mode to AAA authentication, user name to testuser, password to and user privilege level to 15. set authentication password cipher user privilege level 15 protocol inbound telnet //By default, switches running V200R006 and earlier versions use Telnet and do not need to have this command configured switches running V200R007 and later versions use SSH and need to have this command configured. Set the Telnet login authentication mode to password authentication, password to and user privilege level to 15. Table 1-1 Changing the STelnet/Telnet login password Connect the DB9 female connector of the console cable to the COM port on the PC, and connect the RJ45 connector to the console port on the switch, as shown in Figure 1-2.

Web password wizard serial Pc#

Connect the PC to the switch through the console port on the switch.

Web password wizard serial serial#

If there is no COM port (DB9 serial port) on your maintenance terminal (PC), purchase a DB9-to-USB cable to connect the USB port to the maintenance terminal.

Perform the following operations on the master switch, and run the save command to ensure that the configurations on the master switch can be synchronized to other member switches after other member switches start up.

If multiple switches are stacked, power off these member switches.

Web password wizard serial install#

Perform the following operations, install the standby MPU and run the save command to ensure that the configurations on the active and standby MPUs are the same. Do not power off the device when the device starts.įor a modular switch with dual MPUs, remove the standby MPU before restarting the switch. Perform this operation during off-peak hours. This operation, however, will interrupt services and may cause the loss of configuration and data. You can power off and then power on the device to restart it. To access the BootROM/BootLoad menu, you need to restart the device. Now saving the current configuration to the slot 0. The current configuration will be written to the device.

To prevent configuration loss after a device restart, save the device configuration.

local-user admin123 password irreversible-cipher local-user admin123 service-type terminal

The following example changes the authentication mode to AAA authentication, user name to admin123, and password to system-view.

set authentication password cipher return

The following example changes the authentication mode to password authentication and the password to system-view.

Change the console port login password.

Idx Type Tx/Rx Modem Privi ActualPrivi Auth Int

The command output shows that the privilege level of VTY1 is 15, which has the right to change the console port login password. Run the display user-interface command to check the permissions of all users. User-Intf Delay Type Network Address AuthenStatus AuthorcmdFlagġ29 VTY 0 00:23:36 TEL 10.135.18.67 pass no Username : Unspecified Record the User-Intf field value ( VTY1). The line marked with a plus sign (+) indicates the current user. Run the display users command to check all the users who have logged in to the device.

Use the STelnet account to log in to the device and ensure that the account has a privilege level of 3 or higher.

Web password wizard serial how to#

The following describes how to change the console port login password after logging in to the device using STelnet. If you have an STelnet or Telnet account and administrator permissions, you can log in to the device through STelnet or Telnet, change the console port login password, and save the configuration. Method 1: Log in to the device using STelnet or Telnet and change the console port login password.